Back in the day, “real” race cars didn’t have hood scoops. Instead they had an array of open injector stacks poking through the hood top.

Scoops were superfluous.

But then, Super Stock quickly became the rage.

The diversity in hood scoops is remarkable. For instance, notice the scoop design on this SS/Modified Cobalt. (Image/Wayne Scraba)

With racers struggling to find tenths (or even hundredths) of seconds, fresh air induction suddenly became important. Almost simultaneously, muscle cars became a hot commodity. Plenty of those cars came from the factory with cold air induction packages, and many of these cold air packages were for looks only. They weren’t truly functional hood scoops.

The early beginnings of Pro Stock brought us an abundance of different hood scoop designs, and to a certain degree, the influences came straight from Chrysler Corp. R&D. The Mopar bunch took the direct approach to cold air systems. Factory race cars, such as the 1968 Super Stock Darts and Barracudas, incorporated large forward-facing scoops. A year or so later, a slightly more sophisticated, but equally large scoop appeared on 1969 440 Six Pack cars.

These first Mopar-designed scoops relied on the “boundary layer” principle. With this arrangement, the opening of the scoop wasn’t flush with the top of the hood. Instead, the inlet was raised slightly to account for the air flow passing over the nose and hood of the car. A scoop with an opening flush with the hood surface was essentially mounted in dead air. Placing the scoop in direct line with moving air improved the “ram” factor.

In contrast to the scoop on the Cobalt is the low profile design found on this Super Modified Cavalier (mandated by the NHRA rules for Competition Eliminator). Both work. Both are aero. Both are decidedly different. (Image/Wayne Scraba)

The Grump Factor

Others in the racing biz were paying close attention to the importance of hood scoops. Case-in-point is the late Bill Jenkins’ experimentation that eventually led to the renowned “Grump Lump,” a box-style scoop with a rear entrance. This would eventually evolve into a more-sophisticated hood scoop which made its debut on Jenkins’ last Vega Pro Stock car.

The Jenkins’ scoop was innovative for the time and heavily influenced hood scoop technology for years after. For example, the scoop sidewalls diverged toward the rear (seven degrees of slope, front to rear, according to Jenkins). This setup slowed the air upon entering the front opening, allowing for recovery within the hood scoop plenum.

Hood scoop height was a conundrum because NHRA Pro Stock rules dictated scoop height. Because of this, engine placement in the chassis and the overall height of the intake manifold plenum and carburetors were critical to the scoop layout. Initially, Jenkins attempted to reduce air speed and turbulence over the carburetors by modifying the internal walls of the scoop with an elaborate series of sheet aluminum panels. As you might expect, the back carburetor had little if any air velocity over it, but the front carburetor was still affected by the on-rushing air. To compensate, Jenkins carefully reworked each carburetor.

But Grump wasn’t done yet.

With the use of available flow bench equipment of the era, Jenkins figured out that the hood scoop opening should be as small as practical. Jenkins’ findings revealed that it was only necessary to have an opening large enough to feed the engine while the car was sitting still and producing full power—staging, for example. According to Jenkins’ published research (the Chevrolet Racing Engine by Bill Jenkins; SA Design Publishing Company; printed 1976), this opening size would be approximately 2-1/2 times too large when the car was at speed due to the ram air effect. Because of this, Jenkins added a small bell mouth to the scoop opening. Flow bench exploration on a stationary scoop determined that the bell mouth actually doubled the airflow capacity of the scoop. As a result, Jenkins’ new snorkel scoop made use of a much smaller physical opening.

It’s interesting to note that Jenkins also experimented with boundary layer airflow principles. His tests pretty much concurred with Chrysler’s findings: If the opening of the scoop was too large or too near the actual base of the hood, then the air would “stack up.” In effect, the air actually pushed backward against the floor and out of the scoop opening.

This photo and the next photo show two different scoops that turned up on NHRA Pro Stock cars years ago. (Image/Wayne Scraba)

The Next Evolution

Before the 2016 rule change, Pro Stock represented the leading edge of hood scoop development.

Don Ness Racecraft was the next to push the envelope of hood scoop research. By 1983, Ness began to experiment with various hood scoop configurations that were, in essence, “square back” models loosely based on Jenkins’ original design. Ness’ advantage was that he could physically wind-tunnel test different scoop designs using GM’s facilities.

This Pro Stock scoop and the one pictured above are quite dissimilar in overall shape; however, both have a common theme: Small inlet size coupled with larger bodies. (Image/Wayne Scraba)

Ness used the third-generation Camaros of Reher-Morrison and Frank Iaconio as test mules for his scoops. Based on wind tunnel evaluation, Ness came up with something new—a radical NACA duct scoop which picked up flow considerably. The NACA-induction scoop was definitely radical, and the powers in NHRA land claimed “foul.” The high-tech NACA design became instantly illegal, but Ness felt the NACA scoop design was promising.

Ness also offered an interesting viewpoint on wind-tunnel testing. He noted that wind-tunnel testing is only accurate to a certain degree because the engine doesn’t run in the wind tunnel. A 500-cubic-inch engine running wide open can (and should) have a significant influence upon hood scoop design, Ness said.

The WJ Influence

Warren Johnson and his Oldsmobile factory connection were the next to push hood scoop technology. Warren’s setup was unusual in that it was very round. This scoop stretched from the base of the windshield, swung upward, creating a unique opening. The top corners were rounded, and it was fitted with a flat bottom (looking much like a modified D-shape). Wind-tunnel testing revealed the design was equal to, or better than, any previous “box” or square hood scoop. More importantly, overall drag was reduced. This particular scoop was only available to Oldsmobile-bodied racers, and was primarily developed for use in Pro Stock.

Warren Johnson influenced hood scoop technology in a big way. In his NHRA Speed Reading column, WJ provided insight into hood scoop design and the effects of cold air on horsepower and vehicle performance:

“For every 10-degree increase in air temperature, there is a 1-percent decrease in horsepower. The air under the hood of a typical street car is heated by the radiator, exhaust system, and engine. In contrast, a hood scoop supplies outside air at ambient temperature. The difference in output between a Pro Stock engine inducting 100-degree air and the same engine running on 60-degree air is approximately 4 percent, or about 48 horsepower.

“The amount of pressurization produced by a hood scoop varies as a function of the square of the speed of the vehicle. The formula for calculating pressure is:

0.0000176 x air speed in mph² = ram pressure increase in pounds per square inch (psi).

“If you plug in the numbers, you’ll find an increase in inlet air pressure of .142 psi at 90 miles-per-hour. Standard atmospheric pressure is 14.7 psi, so this represents an increase of just under 1 percent. If the air/fuel ratio is adjusted to compensate for the increased pressure, there should be a corresponding 1-percent increase in horsepower. For a 1,200-horsepower Pro Stock engine, that’s a gain of 12 horsepower. Hood scoop pressurization increases dramatically at faster speeds: It’s 2 percent at approximately 130 miles-per-hour, and 3 percent at 158 miles-per-hour. At the magical 200 mile-per-hour mark, the theoretical pressure increase is .704 psi, or 4.8 percent. That equals 56 “free” horsepower.

“Unfortunately in racing, just as in life, there is no free lunch. The penalty you pay for this increase in inlet air pressure is the extra aerodynamic drag produced by the hood scoop. A hood scoop is inherently dirty in terms of its aerodynamics. You can minimize the penalty with proper radii and contours, but you can’t get rid of it. And because the scoop has to be large enough to enclose the carburetors and intake manifold, you don’t have much latitude to change its physical dimensions and frontal area.

“From all of my calculations, it’s a wash between the increased horsepower from the ram effect and the higher aerodynamic drag produced by the hood scoop. In other words, though we gain horsepower from the increased inlet pressure, we have to use all of that power just to push the hood scoop through the air.”

Turning Back The Clock To World War II

While WJ and Oldsmobile were working on their aero scoop, there were other goings on at Pontiac.

Don Ness Racecraft, in conjunction with the Rod Shop and Pontiac, created the “Rod Shop-Pontiac scoop.” As it turns out, if you take a close look at the air intake scoop found on a vintage WWII P51 Mustang fighter plane, you can see the heritage. Make a properly sized copy and flip it upside down to fit the hood of a Pro Stock car, and you can see the similarities. It didn’t take long before this particular scoop design became standard equipment in Pro Stock. You can still see vestiges of the scoop today on drag cars (see the photos).

Like other designs, the Pontiac scoop saw plenty of wind-tunnel testing in various configurations. The overall shape of the scoop, size and shape of the opening, overall approach angle, angle of the air intake opening, and angle below the scoop opening proved critical. In some cases, airflow improved dramatically, but in others, there wasn’t much. What is done inside the scoop proves just as important as the outside shape (see the Jenkins technology above). Minor changes can sometimes be worth between one and two miles-per-hour in top speed. Much of those tweaks came with a cost—hours upon hours of expensive wind-tunnel time.

What Ness and others learned was that dimensional changes as small as ½ inch make huge differences. Ness discovered the scoops used on the 500-cubic-inch Pro Stock cars were less sensitive to fuel distribution problems than small block combinations. And when single, four-barrel Competition Eliminator cars were factored into the equation, it actually became more difficult to design the proper scoop.

Another consideration is the type of carburetor used. Pro chassis builder Jerry Bickel came up with several scoop configurations based on carb layout. NHRA Pro Stock cars, for example, incorporate conventional Dominator-series carburetors. Bickel’s cars use a slim aero-style scoop with a reduced frontal area, but this particular scoop cannot be used with split Dominators (IHRA mountain motors), which require a wider scoop. Basically, what works on a 500-cubic-inch combination won’t work on a mountain motor. And what works on a mountain motor won’t work on a carbureted Pro Mod.

So what does it all mean?

Simple. Today’s hood scoops are as much a part of the overall combination as cylinder heads, for example. There really isn’t any scoop perfect for any car. Instead, it’s a good idea to contact the scoop manufacturer to get recommendations for a specific vehicle.

A scoop isn’t a supercharger. It can improve the performance of your car, but there are limitations. And there’s certainly more to hood scoop technology than first meets the eye.

Compare this hood scoop with the one in the next photo below. This one is a reproduction Boss 429 scoop. It’s designed to be mounted right on the hood top—right in the stagnant boundary layer of airflow. (Image/Summit Racing)
In contrast to the Mustang scoop above, this Mopar Six Pak scoop mounts in a raised position over the hood to get the opening into the active airstream. (Image/Summit Racing)
Chevrolet made use of cowl scoops on many of their muscle cars. They used the air that struck the base of the windshield. Their testing showed that the air reversed at this point (moving forward). By placing a scoop in this location, they could actually gain some ram effect and at the same time, provide the engine with cool air. This is a Harwood cowl induction scoop available at Summit Racing. (Image/Summit Racing)
The next three slides show different takes on the same forward facing theme. All of these hood scoops are from Harwood. Note the dimensions in photo 11. It shows how much smaller the inlet is in comparison to the actual scoop body. (Image/Summit Racing)
(Image/Summit Racing)
(Image/Summit Racing)
Note the dimensions on this hood scoop. It shows how much smaller the inlet is in comparison to the actual scoop body. (Image/Harwood)
This is a package for dragsters and altered developed by K&N. As you can see, the scoop, the air pan, and the filter have been developed to work in conjunction with each other. (Image/Summit Racing)

***

chevy cobalt drag car launching on a race track
dragster style hood scoop on a chevy cavalier in nhra super modified class
close up of a pro stock style hood scoop on a chevy dragster
close up of a pro stock style hood scoop on a mopar dragster
boss 429 ford reproduction hood scoop
mopar six pack style hood scoop
chevy style cowl induction hood scoop
harwood engine hood scoop for race cars
harwood hood scoop
harwood dragster hood scoop
illustration of hood scoop dimensions
hood scoop kit for dragsters by K&N

The diversity in hood scoops is remarkable. For instance, notice the scoop design on this SS/Modified Cobalt.

In contrast to the scoop on the Cobalt is the low profile design found on this Super Modified Cavalier (mandated by the NHRA rules for Competition Eliminator). Both work. Both are aero. Both are decidedly different.

This photo and the next photo show two different scoops that turned up on NHRA Pro Stock cars years ago. The scoops are quite dissimilar in overall shape; however, both have a common theme: Small inlet size coupled with larger bodies.

Compare this hood scoop with the one in photo 6. This one is a reproduction Boss 429 scoop. It's designed to be mounted right on the hood top--right in the stagnant boundary layer of airflow.

In contrast to the Mustang scoop, this Mopar Six Pak scoop mounts in a raised position over the hood to get the opening into the active airstream.

Chevrolet made use of cowl scoops on many of their muscle cars. They used the air that struck the base of the windshield. Their testing showed that the air reversed at this point (moving forward). By placing a scoop in this location, they could actually gain some ram effect and at the same time, provide the engine with cool air. By the way, this is a Harwood scoop available from Summit Racing.

The next three slides show different takes on the same forward facing theme. All are from Harwood. Note the dimensions in photo 11. It shows how much smaller the inlet is in comparison to the actual scoop body.

This is a package for dragsters and altered developed by K&N. As you can see, the scoop, the air pan, and the filter have been developed to work in conjunction with each other. And yes, these complete setups are available online from Summit Racing (see the website – there are literally hundreds upon hundreds of scoops available).

Author: Wayne Scraba

Wayne Scraba is a diehard car guy and regular contributor to OnAllCylinders. He’s owned his own speed shop, built race cars, street rods, and custom motorcycles, and restored muscle cars. He’s authored five how-to books and written over 4,500 tech articles that have appeared in sixty different high performance automotive, motorcycle and aviation magazines worldwide.