If you are looking for maximum accuracy, it’s a good idea to make sure your height mic reads correctly. We calibrated our dial caliper and then measured the height of our well-used height mic set at 1.800. Our calipers indicated 1.809-inch. This 0.009-inch error isn’t a big issue but it is if you are building a race engine where clearances can be very tight. (Image/Jeff Smith)

I bought a set of TFS valve springs (PN 16918-16) for my Summit 8702 cam for an LS engine and I realized these springs are only good up to a 0.610-inch lift cam. My cam is a 0.612-inch lift. Would these still be okay to use? — J.M.

Jeff Smith: The short answer to your question is yes because the difference in lift is very small. These TFS beehive springs are made by PAC Racing so we looked up the specs on the springs and compared them to the numbers on your camshaft. Let’s look at what the specs tell us.

The camshaft is a Summit Stage 3 hydraulic roller cam for a Gen III LS engine. The specs are 236/246 degrees at 0.050-inch tappet lift with 0.612-inch lift using the stock LS 1.7:1 rocker ratio. The lobe separation angle on this cam is 110 degrees so it’s got lots of overlap.

Valve springs are designed to be used with a given installed height. This is the distance from the spring seat on the head to the underside of the valve spring retainer. The stock installed height for LS engines is 1.80-inch which is the same spec for these TFS springs. When the spring is compressed to this height, it creates a load that PAC specs at 140 pounds. To put this in perspective, the stock LS1 valve springs are rated at 76 pounds at this same installed height. The PAC spring’s increased seat load helps minimize valve bounce at higher engine speeds with camshafts intended to spin past 6,000 rpm.

All springs also offer a max lift number that is generally 0.050-inch away from coil bind, which is the height of the spring when it is fully compressed and becomes a solid stack. The coil bind number for these springs is 1.140 inches. If we subtract 1.140 from the 1.800-inch installed height, this gives us 0.660-inch of total spring travel. TFS lists the maximum valve lift at 0.610, which produces a clearance of 0.050-inch away from coil bind.

Since your cam produces 0.612-inch of valve lift, theoretically this will reduce the clearance to 0.048-inch. The 0.050-inch clearance is just a recommendation for the minimum clearance to coil bind so even if the actual lift was a true 0.612-inch, this would not produce a problem. We mentioned this as a theoretical lift because there will always be a certain amount of deflection in any valvetrain.

Starting from the lobe on the camshaft, to get maximum valve lift we multiply the peak lobe lift by the rocker ratio. So 0.360-inch lobe lift multiplied by the 1.7:1 rocker ratio equals 0.612-inch of valve lift.

With a total spring load of 328 pounds at 0.600-inch lift, this is multiplied times the rocker ratio 328 x 1.7 = 557 lbs. of force. This is the amount of load on the pushrods at near-maximum lift.

This much load will generally cause a certain amount of deflection in the valvetrain. It will compress slightly the engine oil in the hydraulic lifter, it may deflect the pushrod, and it also could cause a small amount of movement in the rocker arm. Plus, as the rocker arm travels across the valve tip, this alters the rocker ratio slightly. All of these things can combine to reduce total valve lift by 0.010 to perhaps 0.020-inch. This is especially true with stiffer springs.

Another concern with big-lift camshafts is to also check the retainer-to-seal clearance when assembling the springs. This is the amount of clearance necessary to prevent the bottom of the retainer from smacking the valve guide seal. If this happens, the seal is damaged and that cylinder will begin to use oil. The minimum clearance spec is 0.050-inch.

All of these specs are predicated on establishing the correct installed height. This can be easily measured with a tool called a height micrometer.

Several cam companies like COMP Cams, Isky, and Summit Racing sell these tools. The installed height number does not have to be the exact spec, but if you are detail oriented, you can adjust installed height by several methods. If the measured height is taller than the spec, shims can be used to reduce the height. This is the most common situation.

So as you can see, your concern over maximum valve lift is not really an issue but it would be a good idea to make sure the installed height is as close to the 1.800-inch spec as possible. This will get the most out of those springs.

Author: Jeff Smith

Jeff Smith has had a passion for cars since he began working at his grandfather's gas station at the age 10. After graduating from Iowa State University with a journalism degree in 1978, he combined his two passions: cars and writing. Smith began writing for Car Craft magazine in 1979 and became editor in 1984. In 1987, he assumed the role of editor for Hot Rod magazine before returning to his first love of writing technical stories. Since 2003, Jeff has held various positions at Car Craft (including editor), has written books on small block Chevy performance, and even cultivated an impressive collection of 1965 and 1966 Chevelles. Now he serves as a regular contributor to OnAllCylinders.