(Image/Wayne Scraba)

Take your pick: Chain hoist or cherry picker.

That’s the standard when it comes to yarding out (and replacing and simply moving) an engine in your ride or around your shop. But how you hook the engine to the hoist is the next question.

The easiest way is to use the hooks many original equipment manufacturers bolted right to the engine. But over time many of those hooks have vanished. Yes, reproductions are available, but there are other methods to consider aside from bolting a chain to the cylinder heads.

The most common cherry picker accessory is a lift plate that bolts to the top of the intake manifold.

Some folks might scoff at using lift plates, simply because they’re held in place by four puny 5/16-inch fasteners. But consider that a single Grade 5, 5/16-inch UNC bolt has an approximate yield strength of 3,300 pounds.

Multiply that by four and it’s easy to see that something like a cast iron Hemi isn’t going to rudely crash to the ground from using lift plates.

There should be more concern over the integrity of the intake manifold threads or even the manifold itself than there is for killing a fastener.

NOTE: Speaking of manifold integrity, it should be obvious that you shouldn’t use a lift plate on a sheet metal intake or on a heavily ported example (we’ll get into some solutions later).

A lift plate that this writer uses (and one that’s shown in the accompanying photos) is an old TPIS job. It was designed by the late Myron Cottrell.

Here’s a little background: Myron was the guy who invented the “mini-ram” to replace Chevy’s convoluted long runner Tuned Port Injection intake manifold. A few years later, when Chevy (and Pontiac) came out with the LT1 for Corvettes, Camaros, and Firebirds, they had a manifold that looked very much like Cottrell’s mini-ram.

But even bigger news when dealing with the then-new 1993 Camaros and Firebirds was the length of the windshield cowl. It was humongous. And getting the engine out meant dropping it out from the bottom (after disconnecting brakes lines and peeling out a bunch of suspension components, not to mention the front cross member).

Cottrell knew hot rodders were more comfortable pulling an engine out from the top so he came up with what he called the “Happy Hooker.” It was a special lift plate designed to bolt to the engine so that it could come out topside. Cottrell set it up so that it would work on carbureted applications (Holley and Quadrajet applications). It’s a slick piece (see the accompanying photos) and a slightly revised edition is still available today from TPI Specialties.

When it comes to lift plates, some enthusiasts really dig the examples that are designed to tilt. One of the coolest available is the pivot plate made by Mac’s Custom Tie-Downs and sold by Summit Racing.

Mac’s notes: “The Mac’s PiVOT is operated by turning the 1/2″ orientation bolt. This bolt is precision-machined to ensure smooth, easy operation with only 25 ft.-lbs. of torque required. This low operating torque gives you the option of using an impact wrench or simply adjusting the engine angle manually with a socket wrench.”

Essentially, it uses the center of gravity to provide control for the engine and transmission (or the engine alone) as you’re guiding it into place.

Cranking the adjustment bolt gently changes the angle. That control allows you to install the engine without fear of damaging a freshly detailed engine compartment or getting it snagged in wiring or plumbing. In terms of applications, the pivot tool is designed to work on several different bolt-pattern carbs including Rochester, Carter, Holley, Holley Dominator, and even Stromberg carbs. Summit Racing also stocks and sells adapters that adapt the tool to different EFI engine combinations. Bottom line: this is a handy, well-executed tool.

What if you have an engine with a heavily ported or sheet metal intake? Then you might consider an engine sling.

There are several different variations. Some are designed with chains that do the actual lifting while others use nylon straps.

Several of the chain jobs can be adjusted to change the angle of the engine as it’s set into place. For example, the K-Tool engine sling has a large hand crank on one end. It moves a bearing mounted drive screw which in turn, allows the engine to tilt. The K-Tool sling has a weight rating of 1,500 pounds.

NOTE: If you use a sling or another device with a drive screw for adjustment, be absolutely positive you lubricate the threads prior to use (it’s messy, but anti-seize is perfect for the job). You’ll thank us!

Most of the nylon strap style jobs are fixed in length but Summit Racing’s (part number SUM-905230) is manufactured with adjustable straps. Most of these slings attach with four points. This makes them very stable. In terms of strength, the strap design slings can support 1,200 pounds, so that means you can install an all iron big block with a transmission attached.

Summit Racing stocks and sells good old-fashioned lift chains too. They come equipped with a center hook and steel tabs that bolt to the engine.

They’re simple to use and inexpensive (part number SUM-G1027 is available for under $20). Another option is a simple sprint car style sling. They’re fitted with 1.75-inch wide nylon strap with a centering ring. Each sling has a 500-lb. rating and many folks simply use two of them for engine installs. Each Crow Enterprizes sling at Summit Racing (part number 11645) sells for approximately $35.

As you can see, there’s more than one way to hook your engine to a cherry picker. “Getting Hooked” has never been easier and there’s something here for every budget. For more, check out the accompanying photos:

The factories often used lift hooks on engines and left them there when the car or truck left the dealership. They often go missing but reproductions are readily available. These examples fit on the back of the block and on the intake manifold. Simple attach a lift chain to the hoist and you’re good to go. By the way, Summit Racing stocks several different examples from the folk at Goodmark. (Image/Summit Racing)
Here’s a closer look at the writer’s old TPIS “Happy Hooker” engine lift plate. It fits multiple combinations (EFI, carburetor, etc.) and installs like most other lift plates – directly on the carb studs or by way of bolts. The big difference between it and a regular lift plate is the hook. It allows the user to remove and replace an engine in a fourth gen Camaro or Firebird. (Image/Wayne Scraba)
This is conventional lift plate from Summit Racing (Part Number SUM-G1015-1). It fits most two and four barrel carb setups and has a max load rating of 1,000 pounds. (Image/Summit Racing)
The Mac’s system makes use of an articulating layout that pivots the weight of the engine, tilting it along with an attached trans up to 35 degrees. The big bolt is the key to adjusting the angle. (Image/Summit Racing)
You can buy chain slings that come equipped with a handle that adjusts the engine angle. This one (mentioned in the text) is from K-Tool. (Image/Summit Racing)
What makes the Summit Racing lift sling setup different than other is that it can be adjusted. The bar is 26-inches long while the straps have a base length of 24-inches. (Image/Summit Racing)
Yes, you can still use a good old fashioned chain to yank out an engine. Here’s a good example available right here under part number SUM-G1027. Chain length is 34-inches and it has a capacity of 600 pounds.
This is the Crow Enterprizes nylon sling mentioned in the text. Each sling is approximately two feet long with a 7/16-inch diameter hole in each tab. You’ll likely need two of them. (Image/Summit Racing)
Author: Wayne Scraba

Wayne Scraba is a diehard car guy and regular contributor to OnAllCylinders. He’s owned his own speed shop, built race cars, street rods, and custom motorcycles, and restored muscle cars. He’s authored five how-to books and written over 4,500 tech articles that have appeared in sixty different high performance automotive, motorcycle and aviation magazines worldwide.