Is there a cheap way to increase compression on my small block Chevy? I have a 350 small block with iron heads. I don’t know much about the engine because it came in the car. The previous owner said it was rebuilt and has a cam but he couldn’t remember the specs. The other parts are an Edelbrock Performer intake, a 600 cfm Holley carb, and cast iron exhaust manifolds. The engine runs fine on the cheap 87-octane stuff and doesn’t ping at all. I’m thinking a little extra compression wouldn’t’ hurt but I can’t afford a set of aluminum heads. What do you think? Thanks

J.H.

Jeff Smith: Raising the compression ratio is an excellent idea for several reasons. Assuming that the added compression is not excessive, adding compression is the best way to improve power while also improving efficiency. There’s a reason that all the latest generation LS engines and especially the new gasoline direct injection (GDI) LT1 Corvette engine have higher compression ratios. The LT1 is designed to operate with premium fuel but comes from the factory with a true 11:1 static compression ratio.

Having said that, you can’t run that much compression on a small block Chevy using older, ‘70s vintage iron heads. We won’t get into all the details as to why but suffice to say that those older combustion chambers were not designed to accommodate that kind of compression. Internal combustion engineering has come a long way to achieve these higher static compression ratios and still operate on 91-93 octane fuel.

Since we don’t know much about your 350 small block, we’ll assume it employs the typical flat top, four eyebrow production pistons. With a composition head gasket, the piston 0.020-inch below deck, and a 76cc combustion chamber, and with a composition head gasket this puts the static compression at 8.5:1. This really isn’t bad. The standard Chevy 290-horsepower 350 Chevy crate engine you can buy isn’t even that good. Chevy’s literature states this is an 8:1 compression engine, and that’s what we found when we measured one of these engines a couple of years ago. This engine uses a dished piston with 13 cc’s of volume that reduces the compression.

One of the dimensions that is not easily changed is the distance from the piston top to the deck. In my compression ratio equation, I assumed the piston is 0.020-inch below the block deck surface, which is excessive, but we can use that to our advantage. If the pistons are closer to the deck (0.005-inch below for example), this improves the compression ratio but also limits the thickness of the head gasket since we are limited to roughly 0.040-inch for piston-to-head clearance. With a 0.020-inch negative deck height, this means we can use a thinner head gasket to improve the compression.

Of course, this means removing the cylinder heads to make this improvement and that’s where many guys don’t want to make the effort. Here’s how it works. We’ll assume that your engine is currently using a composition head gasket. These are quality head gaskets but are generally 0.041-inch thick. Adding the 0.020-inch deck height to the 0.041-inch head gasket creates a distance of 0.061-inch between the top of the piston and the flat portion of the cylinder head. This is called the quench area.

It’s interesting that many enthusiasts tend to overlook the combustion space as a place to improve engine power. The quench area is that flat portion of the piston that matches the flat portion of the combustion chamber on a wedge type cylinder head.

When the piston achieves top dead center (TDC), this creates a very tight clearance between the flat portion of the piston and the flat portion of the head. This area is called the quench space or sometimes called squish–which is a really good descriptor of its purpose. The quench area is designed to squeeze the trapped air and fuel in this area and squish it into the combustion chamber, creating turbulence. The key to quality combustion is to mix the air and fuel – or homogenize it. The quench area helps this process which tends to stabilize the speed of combustion once the spark plug lights.

The tighter you can get this quench area–or the piston-to-head clearance–the better the engine will run. Moving the piston closer to the deck surface also increases the static compression ratio. There is also a limit to piston-to-head clearance. Generally, for a low rpm street engine, you could be safe at 0.040-inch or slightly tighter. High rpm race engines with steel rods will fit into the same clearance but aluminum rod engines must use more clearance (perhaps around 0.050-inch) to accommodate the growth of the aluminum rods.

This photo shows checking the piston-to-deck clearance with a dial indicator. This is important information for blueprinting an engine and for accurately calculating the static compression ratio. It’s also critical for knowing the piston-to-head clearance.

Since it will not be feasible to disassemble your engine and deck the block, there’s an alternative idea. Fel-Pro makes a steel shim head gasket with a very thin rubber coating for a 4.00-inch bore 350 that is only 0.015-inch thick. When added to your 0.020-inch deck height, this produces a 0.035-inch piston-to-head clearance. This is a little tight but should be fine for a mild street engine that does not see engine speeds beyond 6,500 rpm.

The good news is that this gasket will bump the static compression ratio up to 8.97:1 or essentially 9:1, which is worth roughly a half a point in compression. A rule of thumb for engine is that a full point of compression is worth roughly 3 to 4 percent of engine power. Assuming 300 horsepower on your engine, a half-point of compression is probably worth almost 2 percent – which is only 6 horsepower. That sounds like a lot of work for a minimal improvement, but my guess is that low-speed torque will also improve at least this much if not perhaps a bit more.

Here is a photo of a 290-horsepower small block with dished pistons. If your engine has these pistons, expect the compression to be around 8.0:1 which is at least 1.5 ratios away from where it needs to be. The easiest way to improve compression is with a set of 64cc chamber cylinder iron Vortec heads and that 0.015 head gasket, which will push the compression up to 9.0:1

One further recommendation would be to add a set of mid-length headers to the engine. This will do more to add power than any other thing you can do. Adding headers on a 290-horsepower small block was worth 30 ft.-lbs. of torque and 30 horsepower to that otherwise stock engine. My suggestion would be to do both the head gasket and the headers and then you will definitely need to re-jet the carburetor slightly richer unless it was excessively rich to begin with–which is also possible.

Share this Article
Author: Jeff Smith

Jeff Smith has had a passion for cars since he began working at his grandfather's gas station at the age 10. After graduating from Iowa State University with a journalism degree in 1978, he combined his two passions: cars and writing. Smith began writing for Car Craft magazine in 1979 and became editor in 1984. In 1987, he assumed the role of editor for Hot Rod magazine before returning to his first love of writing technical stories. Since 2003, Jeff has held various positions at Car Craft (including editor), has written books on small block Chevy performance, and even cultivated an impressive collection of 1965 and 1966 Chevelles. Now he serves as a regular contributor to OnAllCylinders.