With the upcoming addition of the 454-cubic-inch big block to my 1966 El Camino, I begin to worry about the durability of the 8.2-inch 10-bolt rear. It currently houses a 3.36:1 gear ratio which I am very happy with. The car itself is a driver, I do not drag race, nor do I anticipate ever taking it to the track to do so although I plan to do more than a few aggressive accelerations on occasion. But for the most part, the car isn’t going to be abused beyond the occasional tire fry. I run 255/50’s on the rear.

The present 8.2 is an open diff, so with the big block it isn’t going to ever hook hard enough to break anything, however I would like to upgrade the rear end to a posi at some point and that’s where the concern begins. Can the 8.2 be modified to be survivable behind a big block that may occasionally hook?

 If I reuse the existing gears, it looks like I’ll have about $900 in parts and I expect I’ll spend another $400 in labor to install. This probably isn’t all that different a cost if I applied the same upgrade to a rebuildable 12-bolt, but finding a 12-bolt today is not nearly as easy as it used to be. So the question is, will an upgraded 8.2-inch 10-bolt be reliable behind a street big block that isn’t raced?

E.R.

ASK-02-01Jeff Smith: The essence of car building and hot rodding has always been discovering the weak link in the powertrain chain. This is really a great question and not one that is really easily answered. Rear-end strength is generally measured in terms of torque capacity. But the real issue is traction. An El Camino generally is lighter over the rear tires than a Chevelle, so traction is more difficult to achieve. As long as your tires never completely hook when the power is applied from a dead start, such as at the drag strip, a weaker rear axle like the 8.2-inch 10-bolt will likely survive. That’s the short answer. But if you’ve been reading this column for any time at all, you know we like to get into the details to deliver reliable tech information. So let’s dig a little deeper into this question and see what we come up with.

First, let’s compare the 8.2 10-bolt to the 8.875-inch 12-bolt. These dimensions refer to the ring gear diameters (the 8.2 dimension is really 8.125) and as you might expect, the larger the ring gear, the better tooth contact between the ring and pinion. But there are far more important areas of concern. First, the 10-bolt’s pinion shaft diameter is 1.438 (25 splines) while the 12-bolt is 1.625 (30 splines) which makes the 12-bolt 13 percent larger in diameter and therefore stronger. But it’s rare to see pinion shafts twist. The weak point is actually out at the axle splines. The 8.2 uses a 28-spline axle (1.20 inches in diameter) while the 12-bolt uses a 30-spline axle (1.625 inches in diameter).

The main reason the axles often fail first can be traced to what happens when engine torque is applied to the tires. Let’s take a typical 454 big block Chevy like yours. Even a decent Rat motor with a mild torque converter can produce 330 to 350 ft.-lbs. of torque at 3,000 rpm. Let’s use that as our converter flash point. Torque converters can multiply torque anywhere from 1.8:1 to 2.5:1 times the input torque at stall, which means with 2:1 torque multiplication at 330 ft.-lbs., at that moment the transmission input shaft sees 660 ft.-lbs. of torque. Then multiply that times the first gear ratio (we’ll assume a TH-400) at 2.48:1 (we’ll also assume no efficiency loss just to keep the math simple) which gives us 1,637 ft.-lbs. of torque at the driveshaft. Now multiply that times the rear-end ratio of 3.31:1 which means the differential is experiencing a maximum of 5,418 ft.-lbs. of twisting motion. Split that number in half to put equal torque to both tires and each axle shaft could be subjected to over 2,700 ft.-lbs. of torque. Of course, this assumes perfect traction. This can easily happen, which is why the axle splines could twist or fail since they are the first in line to experience that torque. While an additional two teeth on the splines hardly seems enough, it goes a long way to improving durability.

One way to improve the strength of the 10-bolt would be to upgrade to 30-spline axles, but right now there isn’t a bolt-in way to do this, so you are stuck with using the strongest 28-spline axle you can find. Companies like Moser, as you found, offer a 1541H alloy steel induction-hardened axle that is quite a bit stronger than the production 1040 carbon steel axles. New axles also will require new bearings, seals, and axle studs as well. I’d suggest a Ratech installation kit. I’ve used their kits in several applications with great success.

I created a list of the major components including reusing your existing 3.36:1 gears. The total comes to just over $1,000 plus approximately $400 for installation labor at a professional shop. That’s roughly $1,400—a big-dollar expenditure for a 10-bolt. However, you make a good point about buying a used 12-bolt housing that we’ll assume will need to be completely rebuilt including new gears and a posi. With that scenario you’re looking at a used 12-bolt for around $600 to $800 and then investing another $1,400 or more to bring it back to life. But then you would have a new rear axle housing that you know without a doubt will handle any abuse you can dish out. My estimate is that the combination of a set of 255/50R17 street tires on the back of your El Camino will not present sufficient traction—even with a set of sticky Mickey Thompson ET Street tires that grip really well. I think if you drive the El Camino sanely, with the knowledge that it is just a 10-bolt, it will hold up just fine.

8.2 Rear Axle Component List

Component Part Number Price
Yukon Dura-Grip posi YDGGM8.2-3-28-1 $482.13
Moser axles, pr. A102802 $259.97
Moser wheel studs, 7/16 8060 $17.50
Ratech gear install kit 3020K $111.97
Summit Racing diff cover SME-8510300 $149.97
Author: Jeff Smith

Jeff Smith has had a passion for cars since he began working at his grandfather's gas station at the age 10. After graduating from Iowa State University with a journalism degree in 1978, he combined his two passions: cars and writing. Smith began writing for Car Craft magazine in 1979 and became editor in 1984. In 1987, he assumed the role of editor for Hot Rod magazine before returning to his first love of writing technical stories. Since 2003, Jeff has held various positions at Car Craft (including editor), has written books on small block Chevy performance, and even cultivated an impressive collection of 1965 and 1966 Chevelles. Now he serves as a regular contributor to OnAllCylinders.