Tech / Tech Articles

More Cheat Sheets: 13 Key Automotive Formulas You Should Know

How do you calculate compression ratio? What’s the best way to figure out engine displacement?

Image/Pixabay

In the automotive mechanics world, there are formulas and conversions for measuring just about everything—from horsepower and torque to carburetor cfm and gear ratio. The key is remembering them.

While cheat sheets might have frowned upon in your sixth-grade classroom, we strongly encourage them in the garage, shop, or pits. That’s why we’ve put together this list of 13 key performance formulas you should know when building or tuning your street or race vehicle.

Read it, print it out, and tape it to your beer fridge. (Quick—while your sixth grade teacher isn’t looking!)

Racing Carburetor CFM

Racing Carburetor CFM = RPM x Displacement ÷ 3456 x 1.1
Note: Summit Racing also offers this CFM Calculator to make the job easier.

Displacement

Displacement = .7854 x Bore2 x Stroke x Number of Cylinders

Correct Compression Ratio (CCR)

CCR = FCR (Altitude/1,000) x .2
Note: You can also take this Compression Ratio Calculator tool for a spin.

Tire Diameter

Tire Diameter = (MPH x Gear Ratio x 336) ÷ RPM

Rocker Arm Ratio and Valve Lift

Gross Valve Lift = Camshaft Lobe Lift x Rocker Arm Ratio

Horsepower

Horsepower = (RPM x Torque) ÷ 5,252

Torque

Torque = (5,252 x HP) ÷ RPM

Rod Ratio

Rod Ratio = Rod Length ÷ Crank Stroke Length

Average Piston Speed

Average Piston Speed = Crank Stroke x RPM ÷ 6

Rear Gear Ratio

Rear Gear Ratio = (RPM at Finish Line x Tire Diameter) ÷ (MPH x 336)
Note: You can also save this link to a handy Gear Ratio calculator.

Volume (CCs) of Deck Clearance

CCs of Deck Clearance = Bore x Bore x 12.87 x Depth of Deck Clearance

Volume (CCs) of Head Gasket

CCs of Head Gasket = Bore x Bore x 12.87 x Thickness of Head Gasket

Compression Ratio

Combined Chamber CCs + Gasket CCs + Deck CI CCs + (Displacement x (N))

÷

Combine Chamber CCs + Gasket CCs + Deck CI CCs

(N) = 2.0483 for  8-cylinder. (N) = 2.7311 for 6-cylinder. (N)=4.0967 for 4-cylinder.

Tags: , , , ,

22 Comments

  1. Pingback: Methods of measuring volume of the cylinder head.

  2. Pingback: Back to School Supplies: Automotive Formulas, Calculators & More - OnAllCylinders

  3. Pingback: Monday Mailbag: How to Calculate Carburetor CFM - OnAllCylinders

  4. i do not use silicon pistons, it cost me a race motor just replacing stock pistons with hypertectic ones? i thought i looked them over good? but looking after it blew up the wrist pin hole one the one that let loose was made too thin around the pin? it jerked it right out of the one piston, after looking at all the pistons together the one had less writ pin material around it, so be cautious using non factory/or forged pistons, even with low compression, like i had. lost a reliable motor over 100.00 pistons…..

  5. Very good stuff

  6. I really like this, but… Technically compression doesn’t start until the valves are all closed, so the stroke doesn’t start until well after BDC. so with variable valve timing we get a variable compression ratio. With fixed timing, a high calculated ratio is actually quite low when int closure is taken into account

    • Compression Ratio is a fixed “mechanical ratio”, not to be confused with cylinder “pressure”, which is what you are referring to. The ratio never changes, while the cylinder pressure changes constantly, depending on the many variables that are constantly changing through out the stroke of the piston, valve timing, etc.
      And technically, compression “starts” while both valves are still open! (during the overlap cycle of the valves when the exhaust velocity causes the intake charge to get a head start on the cylinder filling, before the exhaust valve closes, and even before the piston starts it’s downward movement. The compression “ratio”, is a totally separate measurement, not even related to the compression itself.
      If we were actually talking of “effective compression ratio” then it would be another story all together, which is where you are headed, and most people, even some professional mechanics, don’t fully understand.

      • BiLL Thompson says:

        I disagree with yours comment, technically compression”starts….during overlap, there is compression on the exhaust stroke forcing exhaust out, Intake stroke create vacuum, Cyl vacuum continues to bottom dead center of the intake stroke, compression “starts” after vacuum is diminished on the compression stroke which is a few degrees past bottom dead center. I’m a 1970 graduate of Nashville Auto Diesel College, they did not teach us how to fix anything, they taught us how things work, if you know how something works, you can figure out what’s wrong with it.

  7. Pingback: Motorhead Math: 13 Essential Calculators to Make Gearhead Math Simpler | MEP Precision Racing

  8. I once had a book that had all of the engine formulas in it including determining the proper diameter, length, and length of collector. of exhaust pipes by where you wanted the torque to peak, same for intake runners. It also had formulas for selecting cam shafts, for proper torque peak tuning.

  9. Looking at a compression ratio is showing minimum or maximum displacement through the head just goes to show how smart these guys in here are wanting to argue with math

  10. This site has a bunch of useful ones too,

    http://www.gtsparkplugs.com/AutomotiveCalculators.html

  11. Explain why I need to factor in number of cylinders to get the compression ratio… I would think all the cylinders are balanced which would kill the need to know the other 7 on a V8…I.E. Deck clearance + head gasket thickness + combustion cc +/- piston dish ÷ cylinder cc = Compression ratio…

  12. Adger Smith says:

    Looks like that formula uses displacement as the known swept vol. So it uses number of cylinders vs displacement to get the swept vol down to one cylinder.

  13. Don Cunningham says:

    I’m a retired mechanic. I have known of a few formulas that are needed in shop work.
    I have many car related books and magazines so I do not need to remember most.
    I have always remembered cubic inches formula by memory.

  14. Pingback: Automotive Maths – What Does Phil Know?

  15. Pingback: Mailbag: The Math Formula for Determining Carburetor Size - OnAllCylinders

  16. Pingback: Automotive Calculators

Leave a Reply to Hank Cancel

Your email address will not be published. Required fields are marked *

*

This site uses Akismet to reduce spam. Learn how your comment data is processed.