Phoenix Systems Reverse Brake and Clutch Bleeder Tool

(Image/Wayne Scraba)

One of the most troublesome jobs in hot rodding or racing is brake (or hydraulic clutch) bleeding.

Historically, the common method for bleeding brakes has been to have one person in the vehicle as the pedal pusher, a second person at the brake caliper or drum brake wheel cylinder.

Typically, there’s a hose attached to the bleeder screw leading to a container partially filled with clean brake fluid. With the system topped up at the master cylinder, the pedal pusher slowly depresses the pedal while the person at the bottom end controls the opening and closing of the bleeder screw.

And this method works when everyone is on the same page. If the pedal pumps are herky-jerky, or if the master cylinder runs dry, or if the guy at the bleeder gets the timing wrong, then some of the air will be trapped in the lines. The result is usually a spongy brake pedal.

A Better Way

There’s another option. A pressure or reverse bleeder.

Pressure bleeders work great, but can be expensive (some exceed $500). A far less costly option is the Phoenix Systems Reverse Brake & Clutch Bleeder (currently less than $55).

While it’s a plastic tool and might appear flimsy, it’s actually well-made and well-suited for the do-it-yourselfer.

You May Want to Read: 

Video How-To: Make Brake Bleeding a One-Man Job with the Latest Brake Bleeder Kits

This is an older Phoenix “injector” tool straight out of the author’s toolbox. Newer examples have a different color scheme, but they’re identical in terms of function. Depending which way you orient the tool, it can be used to reverse bleed the brakes or to vacuum bleed the brakes. (Image/Wayne Scraba)

Here’s how it works:

Reverse bleeding is performed when fluid is introduced into the system at the lowest point. According to Phoenix Systems: “The Reverse bleeding system takes advantage of the Laws of Physics: Air rises in fluid. The master cylinder is bled by pushing the air up through the master cylinder reservoir. This is the best overall bleeding technique, however there are times when pressure or vacuum bleeding is desirable.”

To begin the reverse bleeding process, set up the bleeder tool as follows:

  • Begin with a fluid source (typically a fresh can/bottle of brake fluid).
  • Install the bottle adapter in the top of the fluid source.
  • Install a quick coupler hose in the bottle adapter and install on the Phoenix Systems injector.
  • From there, a hose is attached to the brake bleeder screw. Tip: Have a wrench handy to open and close the bleeder screw.

The rigid plastic hose passes through the fresh brake fluid bottle adapter as shown here. The bottle adapter simply fits through the top of an open brake fluid container. (Image/Wayne Scraba)

Start the bleeding process at the right rear wheel (which is typically the wheel furthest away from the master cylinder).

Prime the bleeder system. To accomplish this, lightly squeeze the injector handle prior to attachment to fill the fluid void between the brake fluid can, and the brake bleeder screw.

Next, the rigid plastic hose is attached to the clear flex hose by way of these two connectors. (Image/Wayne Scraba)

Remove the master cylinder cover and open the bleeder screw. Gently depress the injector handle 3-10 times (the amount of fluid injected depends upon the volume of your brake system). Typically, the first wheel will require more fluid than the rest. Remove the adapter from the bleeder. Allow a small amount of fluid to drip from the bleeder. This causes the wheel cylinder or caliper to burp trapped air. Then close the bleeder screw.

Keep an eye on the fluid level in the master cylinder. If it gets too high, then you’ll have to remove some fluid. A large syringe can be used for this task or you can use the reverse bleeder to pull fluid out. Tip: Don’t remove too much fluid.

The clear flex hose simply pushes on to the nipple of the Phoenix fluid injector like this. (Image/Wayne Scraba)

Repeat the process on the remaining brake calipers/drums. We typically go to the next wheel furthest away from the master, which is the left rear. Then go to the right front and finally, the left front.

Something else to consider for cars where the master cylinder is angled is to raise the rear of vehicle to level the master cylinder. This prevents air from being trapped in the end of the master cylinder.

Up front, the small diameter clear plastic flex hose with pre-installed quick couplers installs on the nose of the Phoenix fluid injector. (Image/Wayne Scraba)

In some cases, it may be necessary to vacuum bleed the brakes. In this case, you simply reverse the position of the injector so that when the handle is depressed, it allows fluid to be drawn out of the bleeder and injected into the brake fluid bottle or can. Tip: When using this arrangement, watch the fluid in the master cylinder carefully. You don’t want it to run dry.

This system is inexpensive and easy to use. One person can handle the job, and the reward is a firm pedal.

We think it definitely beats the headaches of having two people struggling to bleed brakes.

Finally, the opposite end of the small diameter clear plastic flex hose is attached to the brake bleeder on your drum brake wheel cylinder or brake caliper. (Image/Wayne Scraba)

Author: Wayne Scraba

Wayne Scraba is a diehard car guy and regular contributor to OnAllCylinders. He’s owned his own speed shop, built race cars, street rods, and custom motorcycles, and restored muscle cars. He’s authored five how-to books and written over 4,500 tech articles that have appeared in sixty different high performance automotive, motorcycle and aviation magazines worldwide.